Gridfinity drawer size chart: how many grid units fit your drawer

3D render of the free Binform Gridfinity scoop bin (render, not a photo)

Gridfinity is a free, open modular storage system: bins sit on a baseplate built on a 42 mm grid. Before you print anything, the one question that matters is how many grid units fit in your drawer. Here's the quick way to work it out, plus a ready-made table.

The two numbers to remember

  • 1 grid unit = 42 mm (width and depth). A 1×1 bin is slightly smaller, about 41.5 mm, so it drops into the baseplate.
  • 1 height unit = 7 mm. A 3u bin is about 25 mm tall; a 6u bin is about 46 mm.

How to size a drawer in 3 steps

  1. Measure the inside width and depth of the drawer (not the front panel).
  2. Divide each by 42 and round down. That's your baseplate size in units.
  3. The remainder is leftover space. Under ~10 mm, most people just let the baseplate float or add a thin shim; larger gaps can take a printed spacer.

Then measure the inside height with the drawer closed. Subtract any baseplate thickness (magnet baseplates are taller) to see which bin heights will clear.

Drawer width → Gridfinity units

Pure arithmetic (width ÷ 42, rounded down). Use the same table for depth.

Inside drawer size Grid units Grid length Leftover
8 in (203.2 mm) 4 168 mm 35.2 mm
200 mm (200 mm) 4 168 mm 32.0 mm
10 in (254 mm) 6 252 mm 2.0 mm
250 mm (250 mm) 5 210 mm 40.0 mm
12 in (304.8 mm) 7 294 mm 10.8 mm
300 mm (300 mm) 7 294 mm 6.0 mm
14 in (355.6 mm) 8 336 mm 19.6 mm
350 mm (350 mm) 8 336 mm 14.0 mm
16 in (406.4 mm) 9 378 mm 28.4 mm
400 mm (400 mm) 9 378 mm 22.0 mm
18 in (457.2 mm) 10 420 mm 37.2 mm
450 mm (450 mm) 10 420 mm 30.0 mm
500 mm (500 mm) 11 462 mm 38.0 mm
20 in (508 mm) 12 504 mm 4.0 mm
24 in (609.6 mm) 14 588 mm 21.6 mm

Example: a drawer measuring 12 in × 18 in inside (304.8 × 457.2 mm) fits a 7 × 10 baseplate, with about 11 mm spare on one side and 37 mm on the other. If your printer bed is smaller than the full baseplate, print it in tiles.

What to print first

Most drawers end up mixing a few sizes: 1×1 bins for small parts, 1×2 for pens and bits, 2×2 for bulkier items, plus one or two tall bins at the back. A good first test is a single small bin. It checks your printer's fit on the baseplate before you commit hours of filament.

Free starting point: get our free Gridfinity scoop bin (STL/3MF/STEP) by email, plus 20% off your first order.

Ready for a full set? The Gridfinity Starter Bin Pack has six bins (1×1, 1×2, 2×2, a 2×2 divided, a tall 2×3, and a 1×2 label shelf) in STL, 3MF and STEP. More sizing details are in our Gridfinity sizing guide and FAQ.

Honest note: Binform files are digital downloads only. Our product images are 3D renders, and our bins haven't been physically test-printed for fit yet, so print one small bin first to check against your setup. Gridfinity was created by Zack Freedman; Binform isn't affiliated with him.